Schedules · Setpoints · Optimum start · Heating vs cooling · London

BMS Optimisation and Energy Saving for London Buildings

Most buildings already have the controls to use less energy. They just aren't set up to. We tune schedules, setpoints and sequences on your existing building management system, fix the faults that waste energy, and measure the result against your own baseline.

Call +44 783 456 2366
  • Free site visit in London
  • Measured against your own baseline
  • Usually no new plant needed
Mainteniq London BMS engineer and a facilities manager reviewing zone temperatures on a building management system floor plan

What is BMS optimisation?

BMS optimisation is tuning an existing building management system so heating, cooling and ventilation run only when, where and as hard as they need to. It covers time schedules, optimum start and stop, setpoints and dead bands, weather compensation, fan and pump speeds, and stopping heating and cooling from fighting each other. It is usually the cheapest energy saving a commercial building can make, because the controls are already there.

Mainteniq optimises building management systems across London and a 120-mile radius, and in Manchester, Birmingham, Leeds and Bristol, on Trend, Tridium Niagara, Delta Controls and other platforms. We also set up remote monitoring and analytics. If the system is too old to tune, see BMS upgrades.

Where the energy goes

BMS Energy Saving: What We Tune

Each of these is a setting or a fault, not a new piece of plant. Together they are where most buildings waste energy.

Air handling unit and BMS-controlled plant in a London office plant room
Fans, pumps and air handling units: the biggest energy users a BMS controls.

Time schedules

What we do: Plant times matched to how the building is really used, with holidays, weekends and empty floors taken out.

Optimum start and stop

What we do: Heating starts as late as it can and stops as early as it can while the building is still comfortable at opening and closing.

Night setback

What we do: Lower temperatures overnight and at weekends instead of full heat, or none at all and a struggle each morning.

Heating and cooling apart

What we do: A proper gap between heating and cooling setpoints, so the same space is never heated and cooled at once.

Weather compensation

What we do: Heating water temperature that follows the weather outside, instead of running flat out on a mild day.

Fan and pump speeds

What we do: Speeds set to what the building needs. Small reductions in fan or pump speed give much larger reductions in power.

Overrides removed

What we do: Points left in manual after a visit are found and released, so the strategy is back in control.

Faults that waste energy

What we do: Valves stuck open, failed sensors and dampers that don't move, found in the trend logs and fixed.

Alarm review

Hundreds of Alarms, and Nobody Acts on Them

“The BMS alarms all day, so we just clear them.” When every alarm looks urgent, none of them are, and the one telling you a valve is stuck open and wasting energy gets cleared with the rest.

An alarm review is part of every optimisation. We go through the alarm list, fix or remove the nuisance alarms, set priorities and delays, and send the important ones to the right people. What is left is a short list that is worth acting on.

Nuisance alarms cleared

Alarms caused by bad limits, failed sensors or plant that no longer exists, fixed at the cause.

Priorities set

Critical, urgent and for-information, with sensible delays, so a real fault stands out.

To the right people

Critical alarms routed to whoever can act on them, day or night, including our 24/7 line for contract clients.

How We Optimise a BMS

Measure first, change one thing at a time, and prove the result. No guesses and no promised percentages.

  1. 1

    Baseline

    Meter data and trend logs collected, so we know how the building uses energy now.

  2. 2

    Survey and logs

    Schedules, setpoints, overrides and sequences reviewed on the front end and checked on site.

  3. 3

    Quick wins

    Schedules, holidays, overrides and setpoints corrected first: no cost beyond our time.

  4. 4

    Tuning

    Optimum start, setback, weather compensation, dead bands and fan and pump speeds set properly.

  5. 5

    Fix the faults

    Stuck valves, failed sensors and dampers found during the work are repaired or quoted.

  6. 6

    Measure

    Energy use compared with the baseline, adjusted for the weather, and reported.

  7. 7

    Keep it there

    Monthly or quarterly checks so settings don't drift back, ideally with remote monitoring.

  8. 8

    Report

    A digital report showing what changed, what it saved and what to do next.

Why buildings drift

Why a Well-Set BMS Stops Saving Energy

Optimisation is not a one-off. Buildings change and settings get moved, so a system tuned two years ago is rarely still tuned today.

Mainteniq London BMS engineer checking a building remotely on a laptop
Remote monitoring catches drift before it shows up on the bill.

Quick fixes become permanent

A point put in manual to stop a complaint on a cold morning, and never put back.

Occupancy changes

Hybrid working, empty floors and new tenants, while the schedules still assume a full building five days a week.

Parts wear

Sensors drift and actuators stick, so the BMS thinks it is in control when it is not.

No one owns it

The facilities team changes, the contractor changes, and nobody looks at the trend logs.

Alarms ignored

So many nuisance alarms that the one telling you about a wasteful fault goes unseen.

Nothing to measure against

Without a baseline nobody can tell if the building is getting better or worse.

Settings and spanners

Savings That Need a Spanner as Well as a Laptop

Some savings are settings. Many are not: a heating valve stuck fully open, a seized damper, a pump running at full speed because its drive was put in hand, or a fan coil unit with a blocked filter. A controls-only contractor can find these in the logs but has to hand them on.

Mainteniq maintains the mechanical plant as well as the controls, including air handling units and heat pumps, so the faults we find during optimisation are fixed by the same team. See air conditioning and heating maintenance and heat pump servicing.

Valves and dampers

Stuck valves freed or replaced, actuators stroke-tested, dampers made to move again.

AHUs and fan coils

Filters, belts and fans on air handling units and fan coil units, so the airflow the BMS asks for is the airflow delivered.

Re-checked in the logs

Each fix confirmed in the trend logs afterwards, so the saving is measured, not assumed.

What the Carbon Trust Says Controls Can Save

10%

energy costs that optimum start can save compared with fixed time controls

8%

rise in heating costs for every 1°C a building is overheated

10%+

of total energy costs a building energy management system can save

30%

rise in energy use, up to, when regular maintenance is not done

Source: Carbon Trust, Heating, Ventilation and Air Conditioning guide (CTV046, 2017). General guidance, not a guarantee. Savings vary with the building and the system, so we measure yours against your own baseline. Our BMS overview explains the wider range buildings typically see.

Regulation and reporting

Why Building Owners Are Looking at Their BMS Now

Energy rules for commercial buildings keep tightening. A well-optimised BMS, with data to prove it, helps with most of them.

ESOS

Large organisations (250 or more staff, or over £44m turnover and £38m balance sheet) must audit their energy use, including buildings. Phase 4 qualifies on 31 December 2026, with notification due by 5 December 2027.

MEES for commercial lets

Let commercial buildings must currently have an EPC of at least E. In its June 2026 response the government dropped the earlier 2027 and 2030 steps and set EPC B from 2031 for let non-domestic buildings over 1,000 m², where cost-effective, which still needs legislation.

Part L: BACS

When a building automation system is installed or replaced in a building with over 180kW of heating or cooling, Approved Document L expects it to monitor, log and analyse energy use and detect losses in efficiency.

TM44 air conditioning inspections

Air conditioning systems over 12kW need an inspection at least every five years. See TM44 inspections.

Heat networks

Since 27 January 2026 heat networks in Great Britain are regulated by Ofgem. Low return temperatures from every flat improve the whole network; see heat network maintenance.

This is a summary, not legal advice. Dates and thresholds are as published by the UK government at the time of writing.

BMS Platforms We Work On

Modern, older and mixed systems, including buildings where nobody has the passwords or the original files any more.

Trend Tridium Niagara Delta Controls Titan Products Distech ControlsJohnson ControlsSiemensHoneywellSatchwellCylonOlder and obsolete systems

How BMS Optimisation Works With Us

  1. 1

    Free site visit

    We look at the BMS, the panels and the plant it runs. Free in London; in the Home Counties, free for larger jobs, otherwise we quote the visit first.

  2. 2

    Digital report with photos

    What we found, what it means and what to do first, sent by email.

  3. 3

    Clear recommendation

    Explained in plain English and priced as a fixed quote before any work starts.

  4. 4

    Work done and recorded

    Every visit ends with a new report, readings and a fresh backup of the system.

Digital reports, not paperwork

A photographed PDF report after every BMS optimisation

No handwritten job sheets and no chasing. Our engineers complete each job electronically on site in Maintivo, our job management system, so the report is built as the work happens: photos, readings, work done and recommendations.

You receive it as a digital PDF by email the same day, with certificates attached where they apply, ready to forward to a landlord, a freeholder, the directors or an insurer.

  • Before and after photosEvery unit and fault photographed on site
  • Readings and checksTemperatures, pressures and test results recorded
  • Work done and next stepsWhat was fixed, what needs quoting, when we return
  • Sent the same dayDigital PDF report by email, ready to forward

Example layout. Completed on site in Maintivo.

Qualifications Behind Our BMS Optimisation Work

SafeContractor ApprovedMAINTENIQ LTD, SSIP certificate NZ2372
BMS Control Systems trainedInnotech / Uxbridge College: DDC, programming, iComm, fault-finding
REFCOM F-Gas certifiedREF1024168, air conditioning and refrigerant work
SAV Advanced HIU Service EngineerHeat interface units in communal heating
NICEIC Domestic VentilationDV-02 certified
NICEIC certified electriciansElectrical work; gas work by Gas Safe registered engineers

Where We Carry Out BMS Optimisation

All 32 London boroughs, with a free site visit, and a 120-mile radius of the Home Counties, where the visit is free for larger jobs and quoted first for smaller ones. We also take on BMS work in these cities:

Outside London? Send us your BMS details

What customers say on Google

5.0Google rating
“I've had the pleasure of working with Petru and his team on a number of maintenance jobs, and they've always been fantastic. They're professional, reliable, and complete every job to a really high standard. Petru is incredibly knowledgeable and it's clear he takes pride in his work.”

Deborah L.

Google review

“Excellent service. Price assessment: reasonable price.”

Attila B.

Google review

“The team is knowledgeable, efficient, and attentive to detail. A great choice for anyone looking for reliable maintenance services. Highly recommended!”

Ben

Google review

Read all reviews on Google

Book a Free BMS Optimisation Visit

In London an engineer comes to look at your BMS settings and plant for free; in the Home Counties it is free for larger jobs, and for smaller ones we quote the visit first. You get a digital report with photos, the quick wins we found and a fixed quote, with no obligation to go ahead.

WhatsApp us Call

BMS Optimisation and Energy Saving: Common Questions

BMS optimisation is tuning an existing building management system so heating, cooling and ventilation run only when, where and as hard as they need to. It covers time schedules, optimum start and stop, setback, setpoints and dead bands, weather compensation, fan and pump speeds, removing overrides and fixing faults that waste energy.

It depends on the building and how far its settings have drifted. The Carbon Trust's guidance says optimum start can save around 10% compared with fixed time controls, that heating costs rise by about 8% for every 1°C of overheating, and that a building energy management system can reduce total energy costs by 10% or more. We measure your building against its own baseline rather than promising a figure.

Usually not. Most of the savings come from settings on the controls you already have. Where we find faulty sensors, stuck valves or dampers, we repair them or quote for them. If the system is too old to tune, we will tell you and explain the upgrade options.

Optimum start works out how late the heating or cooling can start and still have the building comfortable at opening time, based on inside and outside temperatures. Optimum stop switches plant off as early as possible before the building empties. Together they cut hours of running every day compared with fixed times.

Usually because heating and cooling setpoints are too close together, a valve is stuck open, or a sensor is reading wrongly. The Carbon Trust suggests a gap of around 4 to 5°C between heating and cooling setpoints. We find the cause in the trend logs and fix it.

We set a baseline from your meter data and trend logs before changing anything, make changes in stages, and compare energy use afterwards, adjusted for the weather. You get a digital report showing what changed and what it saved.

It can. ESOS audits look at how buildings use energy, and good BMS data makes that easier and shows action taken. For let commercial buildings, better controls can support an improved EPC as part of a wider plan, alongside fabric and plant improvements. In its June 2026 response the government set EPC B from 2031 for let non-domestic buildings over 1,000 m², where cost-effective, and ESOS Phase 4 qualifies on 31 December 2026.

Yes. In blocks the BMS often runs the communal heating plant, pumps and ventilation. Lower return temperatures from the heat network, sensible pump speeds and correct schedules for communal areas all reduce energy use, and work alongside our HIU servicing in each flat.

Yes. Every optimisation includes an alarm review. We fix or remove nuisance alarms at their cause, set priorities and delays, and route the important ones to the people who can act on them, so the alarms that are left are worth answering.

We fix it. Mainteniq maintains the mechanical plant as well as the controls, including air handling units, fan coil units and heat pumps, so faults found during optimisation are repaired by the same team and the saving is checked in the trend logs afterwards.

Emergency line. Same-day response across London.

Something broken right now? Speak to an engineer.

A clear price before any work starts, and a written report after. For planned servicing, compliance certificates and contracts, WhatsApp us and we will call you back.

REFCOM certified REF1024168Gas Safe registered engineersSafeContractor approvedNICEIC certified electricians

Emergency HVAC and heating repair in London