HIU Inspection vs HIU Service: What Is the Difference?
Quotes for heat interface units use the words inspection and service as if they mean the same thing. They do not, and the difference changes what you are paying for.
Direct answer: an HIU inspection is a check and a record. The engineer looks at the heat interface unit, takes readings and reports findings. An HIU service is hands-on: strainers are cleaned, the heat exchanger is checked, valves and sensors are tested and settings are reset. Inspection tells you the condition; a service restores performance.
What is an HIU inspection?
An inspection answers one question: what state is this unit in? The engineer opens the cupboard, looks for leaks, damage and signs of overheating, and records what is installed and what it is doing. Typical items include the manufacturer and model, flow and return temperatures, visible condition of pipework and insulation, and any fault codes.
Nothing is necessarily cleaned or adjusted. The output is a report, which is why inspections suit surveys, handovers and spot checks between annual visits.
What is an HIU service?
A service fixes what an inspection would only find. It is planned, hands-on maintenance that follows the manufacturer's guidance for the unit. A thorough service normally includes:
- Cleaning or replacing strainers and filters that collect debris from the network water
- Checking the plate heat exchanger for scaling and fouling, and treating it where needed
- Testing control valves and actuators, including the differential pressure valve
- Checking sensors and temperature settings against the design intent
- Looking for leaks, then recording before and after readings

Inspection vs service: side by side
| HIU inspection | HIU service | |
|---|---|---|
| Main purpose | Find out the condition | Restore and maintain performance |
| Hands-on work | Limited, mostly checks and readings | Cleaning, testing, calibrating, resetting |
| Output | Condition report and recommendations | Serviced unit plus before and after record |
| Best used for | Surveys, handovers, spot checks | Planned annual programme |
| Fixes a blocked strainer? | No, it finds it | Yes |
Which does a block need?
Most blocks need both, at different moments. The manufacturer-led annual visit is the service, as covered in our guide on how often an HIU should be serviced. An inspection earns its place in three situations:
- Taking over a block with no service history, so the programme is priced from real findings
- Before a contract starts, to agree scope and identify units that need repair first
- Between services, after repeated hot-water complaints from the same flats
If a quote is just labelled "HIU maintenance", ask which of the two it is. Our HIU maintenance service sets out what a full service covers, and a block maintenance contract can combine both across every unit.
What does an inspection usually find?
Inspections are valuable because the same handful of problems turn up again and again in blocks that have not been serviced regularly. The report should name them and rank them, so you can budget instead of reacting.
- Blocked strainers, often the cause of weak flow and lukewarm hot water
- Scaled or fouled heat exchangers, particularly in hard-water areas of London
- Seized or sticking valves and failing actuators, which tend to show up when the heating season starts
- Weeping joints and damaged insulation, which can cause damp in the flat or the one below
- Settings that have drifted, such as return temperatures that are higher than the design intent
Each finding then has a sensible route: some are cleared in a normal service, some need a repair visit, and a few mean a unit is nearing the end of its life. Our guide to no hot water in a flat on communal heating shows how these faults appear to residents.
How long does each visit take, and what affects the scope?
An inspection is shorter than a service because nothing is stripped down or cleaned. The scope of either visit depends on the make and model of the unit, whether it is a direct or indirect type, its age and condition, how easy it is to reach inside the cupboard, and whether the building has a building management system that logs readings.
For a block, the larger factor is logistics. Eighty flats means eighty access appointments, so notices, concierge support and mop-up visits for flats that could not be reached matter as much as the work itself. Pricing is therefore tailored to the building, which is why we quote from the unit count and the survey findings rather than a standard rate. Booking the flats in one building together shares the travel and set-up, so the cost per flat is lower than booking them one at a time; our three HIU service levels all work as a group booking.
Why does the difference matter for records?
Heat networks in Great Britain are now regulated by Ofgem, and existing networks must register by 26 January 2027. Whether a particular block counts as a regulated heat network depends on how it is supplied, so check Ofgem's guidance for your building. Either way, a dated record per unit is the easiest evidence that the network is looked after.
An inspection report shows condition. A service record shows that something was done about it. Keeping both on file gives a managing agent a clear history. Our guide to heat network maintenance explains how the pieces fit together.
Industry guidance for heat networks, the CIBSE and ADE Heat Networks Code of Practice (CP1), recommends repeating commissioning and performance verification annually, or at least every two years, over the life of a network. It is being replaced by a technical standard (TS1), currently in draft, so check the current version when you write a specification.
A practical checklist before you book
- Does the quote say inspection, service, or both?
- Is it per unit, and does it include strainers, heat exchanger, valves and sensors?
- Will each flat get a dated report with readings and defects?
- How are no-access flats logged and rebooked?
- Who attends, and are they trained on your HIU make?
Sources
Related services & guides
Talk to a London maintenance specialist
Whether it's one property or a portfolio, we'll put your compliance and servicing on a single planned maintenance contract. Get a no-obligation quote.